10多年专业石材厂家生产批发五莲花石材,五莲红石材,我们更专业

咨询热线:13734320059

当前位置:五莲花 > 新闻资讯 > 常见问题 >

五莲红路边石无缝处理工艺简述

关键词:五莲红路沿石发表时间:2017-06-07
    天然石材作为地板材料广泛使用,高贵、典雅、光能成为人们喜爱的装饰效果。五莲红路沿石养护系统在不断改进的蜡、晶体表面处理过程中,以确保石材表面的光。可以在美国不是石头毗邻缝但尚未处理的好方法,五莲红路边石关节会由于石头铺路或石头本身还不够平滑,有一个接缝,石头一段时间后,失败将不可逆污染,一方面将导致五莲红路沿石黑,另一方面污渍渗入石材毛孔造成石材病变,严重损害整个美丽的石头。石质无缝处理所谓的无缝磨削加工,已经在附近的武连红路边石上设置,颜色和石板类似于特殊的填塞材料,然后使用专业的设备和技术研磨,抛光。
用这种方式处理后,石板会显得大,整体并没有把石头的美分开。建筑技术的石材无缝加工一般有以下步骤:
   1、第一块石头之间的差距原来的清理,然后用一个特殊的石头缝纫机的原石安装缝re-neatly减少差距,这差距的宽度石头降到最低,然后靠近石大理石的颜色胶填补它。(注意:如果您在seam处理之前完成,则不需要从新的开始)。
   2、使用大理石胶水和大理石胶水的石头颜色,以达到完美的颜色,所以接近原色,以提高整体的意义,以达到最佳的视觉效果。
   3、将会被转移到大理石胶水填充,由于大理石胶水的完全固化会有一定程度的收缩,它应该使大理石橡胶略高于石头的水平,所以不需要填塞几次。
    使用抛光抛光抛光的填料,使之与石料形成水平线,增加石料的整体感觉,解决高和低问题之间的差距,以防止间隙再次变黑。用花岗岩翻新的机器,用一种特殊的路边石夹层磨片仔细打磨,使它成为一个整体与石头平铺。
    磨削和抛光:采用专用的花岗石抛光机,从50 - 3000石水磨到磨石磨削加工,使地面光洁如新。
    4、水晶处理:使用石头水晶粉和结晶剂与抛光、晶面磨床磨削的重压下石和水晶粉在高温作用下的物理和化学综合反应,形成一层致密、结晶后硬晶体保护层可以增强的颜色和亮度,还达到防滑、防水、石油和其他效果。在上面的过程中,缝隙将会有一个非常好的亮度,而石头的颜色非常接近,整体的强烈感觉,而且由于大理石胶水抗污,耐水,抗氧化,不再产生黑色的接缝。
五莲红路边石无缝处理工艺简述
Natural stone as a floor material is widely used, noble, elegant, light can be Kam decorative effect by the people love. Wulianhong roadside stone maintenance system in the continuous improvement of waxing, crystal surface treatment process, to ensure that the stone surface of the light. Can be in the United States is not the stone adjacent to the seam but has not been a good way to deal with, Wulian red roadside stone joints will be due to stone paving or stone itself is not enough smoothness and there is a seam cut, stone After a period of time, the seams will be irreversible pollution, on the one hand will cause Wulian red roadside stone black, on the other hand stains penetrate into the stone pores caused by stone lesions, serious damage to the overall beauty of stone. Stone seamless treatment of the so-called seamless grinding process that is already in the shop Wulianhong roadside stone set in the adjacent gap, the color and slate similar to the special caulking agent to be caulking, and then use professional equipment And technology to be grinding, polishing.
  After dealing with this way, the slate will appear large, the whole is not divided the stone beauty. Stone seamless processing of construction technology generally have the following steps:
  1, the first stone gap between the original clean-up, and then use a special stone sewing machine on the original stone installation of the seam in the re-neatly cut the gap, so that the width of the gap between the stone to a minimum, and then close to the stone Color of the marble glue to fill it. (Note: If you have done before the seam processing is no need to start from the new).
  2, the use of close to the stone color of the marble glue and marble glue for the perfect color, so that close to the original stone color to improve the overall sense, to achieve the best visual effects.
  3, will be transferred to the marble glue to fill, due to the full solidification of marble glue will have a certain degree of contraction, it should make the marble rubber slightly higher than the stone level, so as not to fill several times.
  4, the use of polished polished polished and polished filler, so that with the stone into a horizontal, increase the overall sense of stone, and solve the gap between the high and low problems, to prevent the gap again back to black. The use of granite refurbished machine with a special roadside stone gripping grinding plate on the cut bit carefully polished, so that it becomes a flat with the stone as a whole.
  5, grinding and polishing: the use of a dedicated granite polishing machine, from 50-3000 stone water mill from coarse to fine on the stone grinding, resulting in the ground bright and smooth as new.
  6, crystal processing: the use of stone crystal powder and crystallization agent with crystal face grinding machine polishing, under the weight of grinding under the stone and crystal powder in the high temperature under the action of physical and chemical comprehensive reaction to form a layer of dense, hard crystal protective layer The After crystallization can enhance the color and brightness, but also to achieve non-slip, waterproof, oil and other effects. After the above process, the gap will have a very good brightness, and the stone color is very close, the overall sense of strong, and because the marble glue stain resistance, water resistance, oxidation resistance, no longer produce black seam.
联系我们

服务热线:13734320059

Q Q:1524152546

联系人:李经理

地址:山东省日照市五莲县石材产业园B区